sr5guy

Florida Tie Bars? I thought u were from cali. I'm down for a set regardless.

-Matt

__________________
The dude with a chip on his shoulder.

Stop asking me to compare my chip with Telion's damnit. Mines better .

 

Forevralegend

haha very funny sr5guy.. and i suppose your a man that can transform into a car

__________________
mods-
2.5" mandrel exhaust, deleted cat, cold air intake, web cam regrinds, comp cam valve springs, port & polish heads and manifold, tb bypass, egr block, five speed clutch/flywheel, 80a polyurethane mounts all around, type 1 pulley, headers,re-fabed y-pipe, SR5guy Custom Chip, 6speed swap, Apexi safc II, strut bar, F/R sway bars, FL tie bars, tune
243.3 hp 197.7 ftlb N/A dynapack before manual swap
232.8 hp 204.0 ftlb N/A dynojet 10/19/07
13.737 1/4 mile @ 100.207 mph & 2.012 60' NA

Forevralegend

Here are some install directions,

1. first jack up both sides of the car

2. You will then remove all four of these bolts



3. When you get to removing the small tie bar bolts make sure you take note of the alignment position, there is a dot on the frame and lines on the bolt so keep track of where its at. Use a wrench on the other side while tightening and loosening the bolt so you dont change the alignment. Then bolt the small bar on to 40 ft pounds. The bar should slide right on. If it doesn't, dont force it on since you don't want to change your alignment, just use a drill to slightly widen the holes on the bar.



4. When placing on the long bar first remove the four small 10mm bolts that hold the speed sensor wires to the frame. Then place three washers over each bolt, this will give the bar a nice flat surface to tighten to. Tighten the bar on to around 76 ft pounds then zip tie the speed sensor wires to the bar. The zip ties and washers will be included with the bars.

this is what is looks like complete "not including the sway bar"

__________________
mods-
2.5" mandrel exhaust, deleted cat, cold air intake, web cam regrinds, comp cam valve springs, port & polish heads and manifold, tb bypass, egr block, five speed clutch/flywheel, 80a polyurethane mounts all around, type 1 pulley, headers,re-fabed y-pipe, SR5guy Custom Chip, 6speed swap, Apexi safc II, strut bar, F/R sway bars, FL tie bars, tune
243.3 hp 197.7 ftlb N/A dynapack before manual swap
232.8 hp 204.0 ftlb N/A dynojet 10/19/07
13.737 1/4 mile @ 100.207 mph & 2.012 60' NA

Forevralegend

alright guys one more to go and we can get these made!

__________________
mods-
2.5" mandrel exhaust, deleted cat, cold air intake, web cam regrinds, comp cam valve springs, port & polish heads and manifold, tb bypass, egr block, five speed clutch/flywheel, 80a polyurethane mounts all around, type 1 pulley, headers,re-fabed y-pipe, SR5guy Custom Chip, 6speed swap, Apexi safc II, strut bar, F/R sway bars, FL tie bars, tune
243.3 hp 197.7 ftlb N/A dynapack before manual swap
232.8 hp 204.0 ftlb N/A dynojet 10/19/07
13.737 1/4 mile @ 100.207 mph & 2.012 60' NA

EVLegend94

im interested in both. by when do you need the money?

__________________

KMS Strut Bar, Blackend Engine Damper, Injen Cold Air Intake, Type II Intake Manifold, Stromung Exhaust, Telion Chipped ECU, JDM Headlights with 9006 retro fit Ultra Violet HID's, Hella Micro DE's with H3 Ultra Violet HID's, All Red Tail Lights, 19" Racing Hart C2's (TL-S wheels for the winter), KYB GR2's/H&R Springs, FL Tie Bars, Addco Rear Sway Bar, Goodridge SS Brakes Lines, Type II Calipers, Pioneer 5700 In-Dash TV/DVD, 2 12" Kicker CVR's, 1800 Watt Kenwood Amp, 35% Tint, Sunroof Tilt Mod

Forevralegend

i just need it before i go out and buy the materials so the sooner everyone pays the sooner i can get these out to you guys.

*First Post is updated* If anyone still wants to get in on this, hurry up and let me know before its too late, I don't think ill be making these again.

__________________
mods-
2.5" mandrel exhaust, deleted cat, cold air intake, web cam regrinds, comp cam valve springs, port & polish heads and manifold, tb bypass, egr block, five speed clutch/flywheel, 80a polyurethane mounts all around, type 1 pulley, headers,re-fabed y-pipe, SR5guy Custom Chip, 6speed swap, Apexi safc II, strut bar, F/R sway bars, FL tie bars, tune
243.3 hp 197.7 ftlb N/A dynapack before manual swap
232.8 hp 204.0 ftlb N/A dynojet 10/19/07
13.737 1/4 mile @ 100.207 mph & 2.012 60' NA

EVLegend94

I can have the money to you on friday if thats ok with you.

__________________

KMS Strut Bar, Blackend Engine Damper, Injen Cold Air Intake, Type II Intake Manifold, Stromung Exhaust, Telion Chipped ECU, JDM Headlights with 9006 retro fit Ultra Violet HID's, Hella Micro DE's with H3 Ultra Violet HID's, All Red Tail Lights, 19" Racing Hart C2's (TL-S wheels for the winter), KYB GR2's/H&R Springs, FL Tie Bars, Addco Rear Sway Bar, Goodridge SS Brakes Lines, Type II Calipers, Pioneer 5700 In-Dash TV/DVD, 2 12" Kicker CVR's, 1800 Watt Kenwood Amp, 35% Tint, Sunroof Tilt Mod

Forevralegend

sure thats fine no problem

__________________
mods-
2.5" mandrel exhaust, deleted cat, cold air intake, web cam regrinds, comp cam valve springs, port & polish heads and manifold, tb bypass, egr block, five speed clutch/flywheel, 80a polyurethane mounts all around, type 1 pulley, headers,re-fabed y-pipe, SR5guy Custom Chip, 6speed swap, Apexi safc II, strut bar, F/R sway bars, FL tie bars, tune
243.3 hp 197.7 ftlb N/A dynapack before manual swap
232.8 hp 204.0 ftlb N/A dynojet 10/19/07
13.737 1/4 mile @ 100.207 mph & 2.012 60' NA

EVLegend94

Ok then friday it is so im going to say im in.

__________________

KMS Strut Bar, Blackend Engine Damper, Injen Cold Air Intake, Type II Intake Manifold, Stromung Exhaust, Telion Chipped ECU, JDM Headlights with 9006 retro fit Ultra Violet HID's, Hella Micro DE's with H3 Ultra Violet HID's, All Red Tail Lights, 19" Racing Hart C2's (TL-S wheels for the winter), KYB GR2's/H&R Springs, FL Tie Bars, Addco Rear Sway Bar, Goodridge SS Brakes Lines, Type II Calipers, Pioneer 5700 In-Dash TV/DVD, 2 12" Kicker CVR's, 1800 Watt Kenwood Amp, 35% Tint, Sunroof Tilt Mod

IAmLegend

will send payment tomorrow. im excited for these! about how long do u think itll take you to get them made?

__________________

Mods:
Lighted passenger window switches || Iggee seat covers || Telion chip || Blackend engine damper || Custom CAI || Remus specific || Pioneer DEH-P7800 head unit || 2 Infinity 12.1 Perfect subs || Polk 5.25" components front || JBL 3-ways rear || Kenwood KAC-9125D Mono amp || Kenwood KAC-7202 2 channel amp || Yellow top battery || Ground wire kit

Coming soon:
Type II intake manifold swap
Xbox install w/ monitors

Forevralegend

it will take me about a week to get them all done

__________________
mods-
2.5" mandrel exhaust, deleted cat, cold air intake, web cam regrinds, comp cam valve springs, port & polish heads and manifold, tb bypass, egr block, five speed clutch/flywheel, 80a polyurethane mounts all around, type 1 pulley, headers,re-fabed y-pipe, SR5guy Custom Chip, 6speed swap, Apexi safc II, strut bar, F/R sway bars, FL tie bars, tune
243.3 hp 197.7 ftlb N/A dynapack before manual swap
232.8 hp 204.0 ftlb N/A dynojet 10/19/07
13.737 1/4 mile @ 100.207 mph & 2.012 60' NA

mktng

next gb, since i just fixed up my cooling system.
im so in!
just need money..
will there be another gb for this?

Forevralegend

unfortunately i don't think ill do another group buy for these since im a full time engineering student, i dont usually have time to do this kinda stuff.

__________________
mods-
2.5" mandrel exhaust, deleted cat, cold air intake, web cam regrinds, comp cam valve springs, port & polish heads and manifold, tb bypass, egr block, five speed clutch/flywheel, 80a polyurethane mounts all around, type 1 pulley, headers,re-fabed y-pipe, SR5guy Custom Chip, 6speed swap, Apexi safc II, strut bar, F/R sway bars, FL tie bars, tune
243.3 hp 197.7 ftlb N/A dynapack before manual swap
232.8 hp 204.0 ftlb N/A dynojet 10/19/07
13.737 1/4 mile @ 100.207 mph & 2.012 60' NA

mellofelow

Wow... we got action! Ok, PM us the payment info please.

Edit: DOH!! paypal info on first post. Payment Sent!

__________________
Mellow Legend Gallery Link

Stromung Exhaust Feb 2008 special!!!

Buy Count Final:

Muffler = 27
B-Pipe = 18

LS92Sedan

Let me know how long you plan on making these, right now I cant do it cuz Im about to purchase a 94 GS, but maybe within a month if you are still making these or accepting orders I will be in. I like the bars though, always was a fan of the FUT bars and these look to be the same exact concept minus the adjustability.

__________________
http://img.photobucket.com/albums/v2.../signature.jpg