![]() |
![]() |
|
|||||||
| Register | Home | Forum | Active Topics | Photo Gallery | Wiki | AIM Chat | DIY | Search | Today's Posts | Mark Forums Read |
| OEM Parts Selling an OEM car part? Post here! Sponsored by: Hondacuraworld.com |
![]() |
|
|
LinkBack | Thread Tools | Rate Thread | Display Modes |
|
|
#1 (permalink) |
|
Registered User
|
G2 Fogs/Harness/Switch $125 shipped obo
Just got the fogs/harness/mounting brackets and switch from a legend (everything you need to install them) plus installation instruction (for 94-95 but it's the exact same) http://www.abuckabook.com/acura/foglights.pdf
Both lenses are cracked a bit but all there, could fairly easily be superglued on the cracks. I haven't tested these out, does anyone know if I can just hookup 12v power to test them? They were perfect but some idiot pulled the bumper and let it smash to the concrete cracking both lenses. If I can't get $125 shipped, I'll superglue the lenses and put them on ebay. Pics up in a bit when the batteries get finished charging. Got the whole harness plus the relays and switch, there was a single blue wire that went into a connector at the fuse panel and then to the fog harness in front and to a relay (I think) I can label it. What is that wire? Power? I didn't get it because it's fairly involved to get it. Someone who is good at electrical and knows what I'm talking about could make one. Pretty sure it's the main power. It was 14-16 guage wire. Will sell for $125 shipped lower 48, pm me. I do have perfect R lense from another fog, which would mean you only have to glue a single small crack on the L lense, but I would like a bit extra for that. Thanks All Last edited by MXHalofan : 06-18-08 at 02:52 PM. |
|
|
|
| Sponsored Links | |
Advertisement |
|
|
|
#2 (permalink) |
|
VIP Well Wisher
Join Date: Apr 2005
Location: Casa Grande, AZ
Posts: 2,501
|
![]() camera charged up yet? ![]()
__________________
'94 GS 6MT Exterior: JDM headlights & rain visors <> paint job <> retro '91-'93 OEM fogs & bumper <> 17" Konigs Performance: tuned Apexi SAFCII <> Sr5Guy chipped ECU <> Blackend engine damper <> MLS strut bar <> sr79labrat pulleys <> OBX headers <> Custom Y-pipe, Magnaflow Cat & Resonator, Stromung B-pipe & Muffler (All 2.5") <> TB Bypass <> RJ CAI w/ AEM bypass valve <> cross drilled/slotted rotors <> RJ short shifter <> ground wires Interior: Kenwood DDX6019 w/ NAV & Ipod, 2-tone leather |
|
|
|
|
|
#4 (permalink) |
|
VIP Well Wisher
Join Date: Apr 2005
Location: Casa Grande, AZ
Posts: 2,501
|
do you have the plastic bezels too?
__________________
'94 GS 6MT Exterior: JDM headlights & rain visors <> paint job <> retro '91-'93 OEM fogs & bumper <> 17" Konigs Performance: tuned Apexi SAFCII <> Sr5Guy chipped ECU <> Blackend engine damper <> MLS strut bar <> sr79labrat pulleys <> OBX headers <> Custom Y-pipe, Magnaflow Cat & Resonator, Stromung B-pipe & Muffler (All 2.5") <> TB Bypass <> RJ CAI w/ AEM bypass valve <> cross drilled/slotted rotors <> RJ short shifter <> ground wires Interior: Kenwood DDX6019 w/ NAV & Ipod, 2-tone leather |
|
|
|